Click on the above link to read the ATV Scene test ride of our CT Raptor 700.

 

Click on the above link to see the ATVscene.com test video of our CT Raptor 700.

 

Raptor 700 741cc Big Bore Kit......$749.95

Kit includes: New 106mm big bore cylinder, JE hi performance 12.5/1 piston kit, and Cometic EST complete top-end gasket set.

 

 Raptor 700 Off-Road  Motor Package

We have been tuning and setting them up as we would one of our Baja race quads for good power and durability. We have been posting well over 60 horsepower on the dyno running  this set up. A 60+ horsepower motor with high torque numbers (50+ ft lbs) makes the Raptor seriously fast and a blast to ride with lots of bottom. The kit is offered as a motor only package. We highly recommend our CT pipe kit and the fuel management program is required. We have had great success with the Dynatek F.I. Controller, MSD Blaster and  the Dynojet Power Commander III and V. The Dobeck Gen 3 will work, but the Dobeck Gen 2 will not.

Kit includes: CT head porting, 5 angle radius Race valve job, Web cam, honing your cylinder to extract maximum performance and fitment of a JE hi performance 11/1 (pump gas) or 12.5/1 (100 octane) piston kit, valve spring kit with titanium retainers, and top-end gasket set. Your cam is required as a core. Just ship us your head, cylinder, and cam to receive this package. The 11/1 piston is best for 91 octane pump gas and the 12.5/1 requires 100 octane gas. This can be attained by mixing 108-112 race gas 50/50 with 91 octane pump gas. This kit price is for you shipping us your top-end only. If you would like to ship us your complete motor, add $250.00 for R&R of top-end.

PLEASE NOTE: Your head is returned assembled and ready to bolt on and run. This kit price is for you shipping us your top-end only. If you would like to ship us your complete motor, add $250.00 for R&R of top-end.

Raptor 700 Motor Package......$1145.00

 

CLICK Here for Shipping Instructions for Motors

 

CT Raptor 700 Pipe Kits

CT Racing has finished the development of the Raptor 700 pipe. Contrary to popular belief, the fuel injection system does not re-calibrate itself for adding an exhaust system or for any other motor modifications. The stock fuel injection system only re-calibrates for an air density change. Our pipe kit makes the 700 go very lean with the stock settings, as any good pipe will do. Once fuel management is addressed, we are picking up over 10 horsepower. Take a look at the whopping 21 horsepower increase we have at 9000 RPM. The fuel management system does allow for tuning if you do some mods down the road, such as adding a high compression piston, cam, etc.

The kit is shipped with 11 discs as we have found this to make the most horsepower. With 11 discs, we are producing a stealthy 98dBs of sound. That can be easily reduced by removing a couple of discs. We also offer an open turn down end cap for short course racing. The disc system is a U.S. Forestry approved spark arrestor.

 

The dyno chart above shows the stock Raptor 700 horsepower in blue. Our CT pipe with the Dynatek fuel injection controller and the stock air filter with no lid on the air box is shown in red. We get over 50 horsepower with a K&N filter kit.

                                                                                                                                                           

VIEW PRODUCTS AND SERVICES BY CATEGORY BELOW:

EXHAUST / SHOP SERVICES / INTAKE / BIG BORE KITS / ENGINE COMPONENTS / CLUTCH

IGNITION / FUEL INJECTION  / CONTROLS / BRAKES / CHASSIS / AXLE

 

Part #

Description

Price

 

Exhaust

PP-Y700 Raptor 700 Pipe

Raptor 700 exhaust includes a stainless header and muffler with 11 discs.

$538.95

PP-Y700-PK1 Raptor 700 Pipe Kit with Dynatek Fuel Injection Controller

Raptor 700 exhaust kit includes a stainless header, muffler with 11 discs, and Dynatek fuel injection controller.

$709.95

PP-Y700-PK2 Raptor 700 Pipe Kit with Dynatek Fuel Injection Controller and Pro Design Pro Flow Foam Air Filter

Raptor 700 exhaust kit includes a stainless header, muffler with 11 discs, Dynatek fuel injection controller, and Pro Design Pro Flow foam air filter.

$819.95

PP-Y700-PK3 Raptor 700 Pipe Kit with Dynatek Fuel Injection Controller and Pro Design Pro Flow K&N Air Filter

Raptor 700 exhaust kit includes a stainless header, muffler with 11 discs, Dynatek fuel injection controller, and Pro Design Pro Flow K&N air filter with Outerwear.

$839.95

PP-DISC-11K CT Spark Arrestor 11 Disc End Cap Kit with Bolts $89.95

PP-TURN-D   Turn Down End Cap

Turn down tip includes 6 stainless steel bolts.

This turn down tip CT sonic pipe, and any pipe that uses the 4" Supertrapp disc System.

$54.95 

Shop Services
LB-PORT-4V Raptor 700 Head Porting

CT Racing has done significant amounts of flow bench and dyno testing to offer you the best port layout for your application. We highly recommend getting a valve job at the same time the head is being ported. Our CNC valve job ties in with the port work to offer extremely effective flow numbers.

$350.00
LB-022 Raptor 700 3 Angle Valve Job

Quality valve job.

$144.00
LB-023 Raptor 700 5 Angle Radius Race Valve Job

The 5 angle radius Race valve job significantly raises the flow characteristics at low valve lift and definitely shows a horsepower increase throughout the useable power curve.

$192.00
LB-023BV Raptor 700 5 Angle Radius Race Valve Job for +1mm Intake & Exhaust Valves

The 5 angle radius Race valve job significantly raises the flow characteristics at low valve lift and definitely shows a horsepower increase throughout the useable power curve. The 5 angle valve job really shines on big valves as the seat diameter is opened up all the way into the aluminum casting, blending to the port work. Adding +1mm valves to a modified engine package helps the mid to top-end horsepower. Most aftermarket hi compression pistons are clearanced for +1mm valves.

$240.00
LB-010 Split 4 Stroke Cases, Inspect Crank & Trans, & Reassemble $475.00  
LB-018 Disassemble & Reassemble 4 Stroke Top-end (from bottom-end only) $250.00  
LB-019 Disassemble Head, Clean Ports, Lap Valves, & Reassemble $65.00  
LB-026 Rebuild 4 Stroke Crankshaft (labor only) $75.00  
Intake
AF-PD-233 Raptor 700 Pro Design Pro Flow Foam Air Filter Kit $104.45

AF-PD-234 Raptor 700 Pro Design Pro Flow K&N Air Filter Kit $132.95

AF-FC-YFM700B

Raptor 700 Fuel Customs Intake System with Air Box

System includes a high horsepower intake, Fuel Customs K&N type air filter, Outerwear, and air box.

$298.00

Big Bore Kits
CY-Y700-741BBK Raptor 700 741cc Big Bore Kit

Kit includes: New 106mm big bore cylinder, JE hi performance 12.5/1 piston kit, and Cometic EST complete top-end gasket set.

$749.95

Engine Components
PI-JE-284756 Raptor 700 JE Hi Performance Piston Kit - 102mm 10:1 Comp Ratio $186.75
PI-JE-284757 Raptor 700 JE Hi Performance Piston Kit - 102mm 11:1 Comp Ratio $186.75

PI-JE-284758 Raptor 700 JE Hi Performance Piston Kit - 102mm 12.5:1 Comp Ratio $186.75

PI-W8673DA Raptor 700 Wossner Hi Performance Pro Series Piston Kit - 102mm 11:1 Comp Ratio

Available sizes: A (std), B (+.01), and C (+.02).  

$166.45
GA-C3142-EST Raptor 700 Cometic EST Complete Top-end Gasket Set (includes valve stem seals) - 103mm

EST = Extreme Seal Technology

$81.75
EC-HR-4078 Raptor 700 Hot Rods Heavy Duty Crank - Stock Stroke

Main bearings not included.

$301.90
EC-HR-4178 Raptor 700 Hot Rods Heavy Duty Crank - +5mm Stroker

Main bearings not included.

$350.95
EC-WC-81-482 Raptor 700 Performance Web Camshaft.

Raptor 700 Web Billet Camshaft - 275/275 Duration .445/.397 lift .

This cam is made from a billet blank, the billet does not require a core.

This is a great cam that we use on 95 percent of our builds. It has a very wide power curve and is quite fast, we have cleared 75 rear wheel HP using this cam. - Requires valve spring kit part #EC-KW-80-80410.

$358.95
EC-WC-81-481 Raptor 700 Performance Web Camshaft.

Raptor 700 Web Re-Grind Camshaft - 275/275 Duration .445/.397 lift.

This is the same profile as the cam above but it is built from a stock cam Hard welded and Re-ground.

You must ship us your stock cam or pay the core charge and receive a refund when we get your good stock cam ($210.00 core charge)..

This is a great cam that we use on 95 percent of our builds. It has a very wide power curve and is quite fast, we have cleared 75 rear wheel HP using this cam. - Requires valve spring kit part #EC-KW-80-80410.

$233.95
EC-WC-81-492 Raptor 700 Performance Web Camshaft.

Raptor 700 Camshaft - 290/290 Duration .500/.460 lift.

This cam is made from a billet blank, the billet does not require a core.

Improves top-end performance. This is the go to cam for building a drag only or Hill Shooter Motor - Requires valve spring kit part #EC-KW-80-80410.

$358.95
EC-WC-81-491 Raptor 700 Performance Web Camshaft.

Raptor 700 Camshaft - 290/290 Duration .500/.460 lift.

This is the same profile as the cam above but it is built from a stock cam Hard welded and Re-ground.

You must ship us your stock cam or pay the core charge and receive a refund when we get your good stock cam ($210.00 core charge).

Improves top-end performance. This is the go to cam for building a drag only or Hill Shooter Motor - Requires valve spring kit part #EC-KW-80-80410.

$233.95
EC-HC-4064-1 Raptor 700 Hot Cam Camshaft '06-'08

Stage 1 - Good midrange and top end gains. Uses stock auto decompression mechanism. Uses stock valve springs and rockers

Lift (mm): 9.60 intake 8.60 exhaust              Duration (degrees at 1mm): 253.50 intake 243 exhaust

$180.00
EC-HC-4065-2 Raptor 700 Hot Cam Camshaft '06-'08

Stage 2 - Excellent top end and great over rev. Uses stock auto decompression mechanism. Uses stock valve springs and rockers.

Lift (mm): 10.30 intake 8.60 exhaust              Duration (degrees at 1mm): 260 intake 243 exhaust

$180.00
EC-HC-4091-3 Raptor 700 Hot Cam Camshaft '06-'08

Stage 3 - Drastically improves top-end with over rev. Uses stock auto-decompression mechanism. Uses stock valve springs.

Lift (mm): 10.30 intake 8.60 exhaust              Duration (degrees at 1mm): 268 intake 255 exhaust

$180.00
EC-HC-4131-1 Raptor 700 Hot Cam Camshaft '09-'14

Stage 1 - Good midrange and top end gains. Uses stock auto decompression mechanism. Uses stock valve springs and rockers

Lift (mm): 9.60 intake 8.60 exhaust              Duration (degrees at 1mm): 253.50 intake 243 exhaust

$180.00
EC-HC-4132-2 Raptor 700 Hot Cam Camshaft '09-'14

Stage 2 - Excellent top end and great over rev. Uses stock auto decompression mechanism. Uses stock valve springs and rockers.

Lift (mm): 10.30 intake 8.60 exhaust              Duration (degrees at 1mm): 260 intake 243 exhaust

$180.00
EC-HC-4133-3 Raptor 700 Hot Cam Camshaft '09-'14

Stage 3 - Drastically improves top-end with over rev. Uses stock auto-decompression mechanism. Uses stock valve springs.

Lift (mm): 10.30 intake 8.60 exhaust              Duration (degrees at 1mm): 268 intake 255 exhaust

$180.00
EC-KW-80-8043* Raptor 700 Stainless Steel Standard Intake & Exhaust Valves   $38.15 ea
EC-KW-80-8043* Raptor 700 Stainless Steel +1mm Oversize Intake & Exhaust Valves $38.15 ea
EC-KW-80-80410 Raptor 700 Hi Performance Lightweight Racing Valve Spring Kit with Titanium Retainers $168.95

Clutch

CL-H313 Raptor 700 Hinson Billetproof Clutch Basket $235.00
CL-H256 Raptor 700 Hinson Billetproof Pressure Plate $180.00
CL-FSC213-8-001 Raptor 700 Hinson Clutch Kit with Fibers, Steels, & Springs 

The Hinson Clutch kit is the best clutch on the market, well worth the cost over the import clutches marketed elseware.

$190.00
Ignition
IG-Y4-DFS7-21P Raptor 700 Dynatek Programmable Ignition

Direct plug in performance: 4 programmable timing curves, programmable rev limiter, external curve selector switch, plug-in module replacement, and more.

$332.50
Fuel Injection
IG-Y7-416-411 '06-'08 Raptor 700 Dynojet Power Commander III Fuel Injection Module

Direct plug in performance: easy to install, increased throttle response and acceleration, includes an ATV specific map, user friendly software, and more.

$332.45
IG-Y7-22-002 '09 Raptor 700 Dynojet Power Commander V Fuel Injection Module

Direct plug in performance: easy to install, increased throttle response and acceleration, includes "dyno proven" ATV specific map database, user friendly software, and more.

This is the new PC5 with both Fuel and ignition tuning. The ignition can be re-mapped and the RPM range can be extended. You do have to work with Dynojet, on the Rev Extend program (they have you fill out some paperwork).

$399.95
IG-AT-200 Dynojet Power Commander V Autotune Kit

Automatically monitors and adjusts fuel mixture while you ride. For use with '09 and up Power Commander V only.

$236.50
IG-Y7-DFCA-4 Raptor 700 Dynatek Fuel Injection Controller

Direct plug in performance: 3 user selectable base fuel curves, fuel mixture can be enriched or leaned as required, no PC required for tuning or adjusting fuel curves.

$236.55
Controls
CH-FLX-QR1431-** Fasst 1-1/8" Flexx Bars

These are the best off road bars money can buy. Bars come with three different elastomers to get the proper cushioning for your type of riding along with a cross bar pad in your color choice of blue, grey, or red. A 1-1/8" bar mount kit is required.

$329.95
CH-TG-CRHI

Tag T-2 CR High Bend 1-1/8" Fat Bars with Bar Pad

Bars are available in black or silver and bar pads are available in black, blue, or red. A 1-1/8" bar mount kit is required.

$89.95

CH-TG-UNMNT

Tag Universal 1-1/8" Bar Mount Kit

This is a clamp set than converts your stock 7/8" bar clamp to the 1-1/8" Fat Bar set up. Can be used with any brand 1-1/8" bars.

$69.95
CH-ASV-BCRFQ1* '06 Raptor 700 ASV F3 Pro Pack with Clutch and Brake Lever - Black, Blue, or Red $164.95
CH-ASV-BCRFQ3* '07-'08 Raptor 700 ASV F3 Pro Pack with Clutch and Brake Lever - Black, Blue, or Red $164.95
IG-KS Pro Design Tether Kill Switch - Black, Blue, or Red $36.95

  CV4 Billet Tether Kill Switch Mount - Black or Red -  Handlebar mount for Pro Design and Pro Armor  tether kill switches.

This mount allows you to mount your switch to the bar without using up all of the spacing. Allows you to mount the switch much closer to the bend.

 
Order By Description Power Madd Hand Guard Kit

Kit includes hand guards and mount kit. Hand guards are available in blue/black, black/black, silver/black, white/black, yellow/black, and blue/silver.

$52.95

Brakes

BR-SL-RAP-F Streamline Steel-braided Front Brake Line Kit (specify color & length)

Available in black, blue, clear, green, red, or smoke. Some colors and lengths may need to be special ordered.

$92.95
BR-SL-RAP700-R Streamline Steel-braided Rear Brake Line (specify color & length)

Available in black, blue, clear, green, red, or smoke. Some colors and lengths may need to be special ordered.

$42.95
BR-SL-BLC-1 Billet Brake Line Clamp - 1 pair (specify color)

Can be used with any 3/4" or 1" diameter A-arm. Available in black, blue, red, or silver.   

$29.95
Chassis
CH-LR-RAP700AA+2SE Laeger's +2" Sport Edition A-Arms - Stock Shock $615.00
CH-LR-RAP700AA-LT* Laeger's A-Arms - Long Travel (specify length - +0", +1", +2", or +3")

Add $50.00 for adjustable caster.

$795.00
CH-LR-RAP700SA* Laeger's Swing Arm (specify length - +0" or +1") $CALL
CH-LR-RAP700SS* Laeger's Anti-vibration Steering Stem (specify length - +1" or +2")

Bar mount perch kit not included.

$250.00

 

CH-LR-PK-118 Laeger's Steering Stem Perch Kit - 1-1/8" $85.00
CH-LR-PK-78 Laeger's Steering Stem Perch Kit - 7/8" $85.00

Axles

AX-DB-20-1154 Dura Blue Heavy Duty Axle

This axle is a recreational level axle that is twice the strength of the stock axle. It's a cost effective choice when reliability is a prime concern.

$324.00
AX-DB-20-1154SP Dura Blue Eliminator 2+2 Extended Axle

The Eliminator axle used for all forms of racing and high performance applications. Many of the models come with the patented Posi•Lock system which removes threaded sections from the flexing area of the shaft (a source of crack generation).

$400.50
AX-DB-20-1154EX Dura Blue Eliminator X-33 Pin Drive Axle with Cast Hubs

The X-33 axle uses the same superior material and heat treating as the Eliminator. The unique difference is in the design of the wheel hub mounting area. Standard design ATV axles neck down to about 1" in diameter. A splined wheel hub slides onto the axle shaft and is retained with a hex nut. As all ATVer's know, hubs loosen frequently. The X-33 changes all that. The wheel hub is clamped solid and driven by a pin on a 1-3/8" diameter shaft. This axle is rifled to reduce weight near the rotational axis of the ATV. The X-33 allows for 16 different wheel offset alternatives.

$532.80

Home Page